Proteco Shark - 230v Underground Double Swing Gate Kit
| Product | Volt | Weight max per leaf |
Angle max per leaf |
Width max per leaf |
Type | Price | Buy |
|---|---|---|---|---|---|---|---|
| Double Kit Shark Galvanised (Q80A) | 230v |
350kg |
110° |
3.0m |
Underground, Double Kit |
£1,263.12+vat
RRP £1,970.46 |
|
| Double Kit Shark Stainless Steel (Q80A) | 230v |
350kg |
110° |
3.0m |
Underground, Double Kit |
£1,396.22+vat
RRP £2,178.11 |
|
| Underground 180 degree adaptor |
£120.99+vat
|
|
Double Kit Shark Galvanised (Q80A)
Volt: 230v
Weight (max. per leaf): 350kg
Angle (max. per leaf): 110°
Width (max. per leaf): 3.0m
Type: Underground, Double Kit
£1,263.12+vat
RRP £1,970.46
RRP £1,970.46
Double Kit Shark Stainless Steel (Q80A)
Volt: 230v
Weight (max. per leaf): 350kg
Angle (max. per leaf): 110°
Width (max. per leaf): 3.0m
Type: Underground, Double Kit
£1,396.22+vat
RRP £2,178.11
RRP £2,178.11
Underground 180 degree adaptor
Volt:
Weight (max. per leaf):
Angle (max. per leaf):
Width (max. per leaf):
Type:
£120.99+vat
Kit Contents
2 x Shark Motors
2 x Foundation Boxes
2 x Wired Safety Photocells
1 x Q80A Control Board
2 x Radio Remotes
1 x Override Keys (for power cuts)
1 x Safety Blinker Light
1 x External Aerial
2 x Foundation Boxes
2 x Wired Safety Photocells
1 x Q80A Control Board
2 x Radio Remotes
1 x Override Keys (for power cuts)
1 x Safety Blinker Light
1 x External Aerial
Products bought with Proteco Shark - 230v Underground Double Swing Gate Kit
Gate Motors Double Gate Stops Set
2 x Back Stop and 1 x Mid Stop in a black powder coated finish for double gates
£54.65
Proteco RF40 Wired Photocells
1 x RX Receiver & 1 x TX Transmitter Safety Photocells
£84.68
3 x Angie Remote
Proteco Angie 4 channel radio transmitter
£63.36
Need this kit in 24v? Click here
Key Features
- Waterproof aluminium gear motors
- In-built obstacle detection
- Inward or outward opening
- Residential use only
- Simple wiring & programming
- Wide opening angles to 110° (180° with adaptor)
Product Overview
The Proteco Kit Shark motor mechanics are buried within secure steel (choose from galvanised or stainless) underground foundation boxes for ultimate waterproofing and durability.
The fluid-grease lubrication system and the built-in thermal protection ensures a long-lasting working life in any weather conditions without the need for periodic maintenance.
The operators are non-reversible and therefore don’t need the inconvenience or expense of an additional electric lock to keep them closed. However, with this in mind it is always recommended to install ground stops in opening and closing position.
Limited Warranty - 3 years on motors, 1 year on other components. See T&C's for more info.
Kit Suitability
The Proteco Kit Shark underground foundation box is installed beneath the gate at the foot of the hinge pillar.
The minimum distance between the vertical centre line of the hinges and the inner face of the pillar is 65mm. There must also be at least 58mm between the lid of the foundation box and the bottom of the gate.
Before purchasing this kit it is important to note your gate achieves the minimum cleranace as detailed above.
Installation Advice
If fitting underground drivers to wooden gates it will be necessary to clad the gate bottom edge with metal to spread the load and to give something to attach the motor shoe. If you don't, the push/pull from the high torque will eventually split the wood. Some additional fabrication/welding may be necessary to connect the drive shoe to your gates.
Gate Stops
Most electric gate motors require a physical stop at the end of the opening and closing cycle. Gate Stops provide resistance to the motors so they know they've reached either the open or closed position. Without Gate stops the motors will over extend during their operation and the mechanism will eventually fail. When assessing your gate-way it is important to check you can install physical stops in both the closing and opening positions. A Common reason why gate stops cannot be installed is because of a sloping driveway or the gate is raised significanlty off the ground. If you cannot install something to provide resistance at either end of the motors cycle then you will require a specialised ram with in-built mechanical stops.
Need more information or advice on this kit ? Call our sales support team on 01202 717 191 or complete our site assessment form and we can advise the right kit for your installation.
Kit Contents
2 x Shark Motors
2 x Foundation Boxes
2 x Wired Safety Photocells
1 x Q80A Control Board
2 x Radio Remotes
1 x Override Keys (for power cuts)
1 x Safety Blinker Light
1 x External Aerial
2 x Foundation Boxes
2 x Wired Safety Photocells
1 x Q80A Control Board
2 x Radio Remotes
1 x Override Keys (for power cuts)
1 x Safety Blinker Light
1 x External Aerial
